Quick picker
| If the part… | Use | Why |
|---|---|---|
| sits on a desk or shelf | PLA | Cheapest, crisp detail, rigid. Fine at room temperature. |
| gets wet, gets dropped, gets clipped on and off | PETG | Tougher, bends a little before it breaks, doesn't mind water. |
| lives in a car, on a boat, or outside | ASA | Built for UV and holds shape at higher temperatures. |
| has to grip, seal, cushion or flex | TPU | Rubber-like. Gaskets, bumpers, feet, straps. |
| takes real load, or is a jig or fixture | Nylon CF | Carbon fibre makes it stiff, strong and dimensionally steady. |
PLA
PLA is the plastic most people picture when they hear "3D printing". It prints sharp, it's stiff, and it's the cheapest option. It's also the one people regret using in the wrong place, because it begins to soften somewhere around 55–60 °C. A PLA phone mount left in a parked car in Orlando in July will droop.
Good for: display models, architectural and product mock-ups, cosplay pieces that stay indoors, test fits before printing the real part in something tougher.
Avoid for: cars, outdoors, anything near a heat source, anything that snaps on and off repeatedly.
PETG
PETG is in the same family as the plastic in water bottles. It's the default here for parts that do a job, because it flexes slightly before it fails instead of shattering, it handles water, and it takes more heat than PLA (roughly 75–80 °C before it softens).
Good for: clips, brackets, enclosures, pool and irrigation parts, garage organisers, replacement appliance parts.
Avoid for: long-term full sun on a dark surface, where ASA lasts longer.
ASA
ASA is the outdoor cousin of ABS (the plastic LEGO bricks are made from). It was developed to survive sunlight without going yellow and chalky, and it holds its shape to around 95–100 °C. In Florida, this is the answer for anything in a vehicle, on a dock or boat, or mounted on the outside of a house.
Good for: car interior trim clips and mounts, boat and kayak fittings, outdoor sensor housings, gutter and screen-enclosure parts.
Trade-off: it costs more and needs an enclosed, heated printer, which is reflected in the price. ASA jobs run on the H3C printers now arriving, so ASA orders are queued until those are running. Choosing between the two: PETG vs ASA.
TPU
TPU is flexible, like a firm rubber. The common grade, 95A shore hardness, is about as firm as a skateboard wheel or a phone case. It prints slower than the rigid plastics, so it takes more machine time per gram.
Good for: gaskets, bumpers, cable strain reliefs, non-slip feet, protective sleeves, custom grips.
Carbon-fibre nylon
Nylon filled with chopped carbon fibre is the engineering choice: stiff, strong, stable, with a matte black finish that hides layer lines well. It's what you want for shop jigs, robot and drone parts, and brackets that carry real load.
Trade-off: it's the most expensive option here, and nylon absorbs moisture, so it gets dried before printing. Parts are matte black only. Like ASA, it runs on the H3C printers now arriving, so nylon orders are queued until those are running.
More than one material in a part
Some parts want two plastics: a rigid PETG or ASA body with a TPU grip, pad or seal printed straight onto it. That takes a printer with a separate toolhead per material. The Bambu Lab H3C printers on their way to the shop have nine. Here's what that changes for a part you'd order.
When plastic isn't enough
Parts beside an exhaust, threads that get torqued hard, thin tabs carrying real weight: those need metal. Metal 3D printing is being added here. Until it's running, you'll be told straight whether carbon-fibre nylon will do or the part should go to a machine shop.
Why a printed part is weaker in one direction
A printed part is built from stacked layers, and the bond between layers is its weakest direction. That's why the same bracket can be strong or weak depending on how it lies on the plate. Every job is oriented so the load runs along the layers, not across them. If that isn't possible, the part gets redesigned or you're told printing is the wrong method.
Common questions
Can a PLA part go in a car in Florida?
No. PLA starts to soften around 55–60 °C, and a closed car in Central Florida sun regularly gets hotter than that inside. Use ASA for anything that lives in a car.
What is the strongest 3D printing filament?
For stiffness and strength in a printed part, carbon-fibre reinforced nylon is usually the strongest common option. For impact toughness without cracking, PETG and TPU are better choices.
Which filament is best outdoors?
ASA. It was developed for outdoor use, resists UV yellowing and brittleness, and holds its shape at higher temperatures than PLA or PETG.
Temperatures are typical softening ranges for common grades; exact values vary by brand.