Home / Services / Metal 3D printing

Metal 3D printing is coming to Winter Park

Some parts can't be plastic, however good the plastic is. Metal printing is being added to the shop for those. It isn't running yet, so this page says plainly where it stands, which parts it's for, and how to get yours looked at first.

Statusbeing set up, not printing yet
Requestsopen now
Best fileSTEP
AreaOrlando · Winter Park · shipped US-wide

Where it stands

Z-Seam prints plastic today. Metal is the next step and the equipment is on its way, but no metal part has left this shop yet, so there are no prices, alloys or lead times printed here. Those go up when there are real parts to back them.

Until then, send the part anyway. Every metal request gets read by a person. You'll hear one of three things back: it can wait for metal and you're on the list, it doesn't need metal at all, or it needs a machine shop and here's why.

Parts that need metal

  • Heat. Brackets near an exhaust, parts in an engine bay, anything beside a heating element. Even the best printing plastics give up well before metal does.
  • Threads that get torqued. A bolt tightened hard, or taken in and out for years, chews through plastic threads. Brass inserts help, but only to a point.
  • Thin sections under load. A hook, tab or lever that has to stay slim and still carry weight.
  • Wear. Surfaces that slide, pivot or get clamped again and again.
  • Constant load. Plastic slowly sags under a load that never lets up. A shelf bracket holding 20 kg for ten years is a different job from one holding it for a week.

Parts that don't

Most requests that start with "I think this needs to be metal" end up in plastic, because the original was metal for cost or habit, not strength. Jigs and fixtures, enclosures, sensor mounts, cable brackets, drone and robot frames and most replacement parts for appliances and cars do fine in carbon-fibre nylon or ASA, at a fraction of the cost and in days instead of weeks. If plastic will do, that's what you'll be told.

Printed metal or machined metal

If the part…Usually betterWhy
has internal channels, hollow sections or curves a cutter can't reachPrintedPrinting builds the inside and outside at once.
is a one-off or changes every revisionPrintedNo fixturing or programming per design.
is a plate, block or shaft with holesMachinedFaster and cheaper from bar or plate stock.
needs bearing fits or sealing facesMachined, or printed then machinedPrinted metal surfaces are rougher and less exact than cut ones.

What to send

  • A STEP file if you have one. An STL or clear photos with a ruler in the shot work too.
  • What the part does: what it bolts to, what load it sees, how hot it gets.
  • How many you need, and whether that number is likely to grow.
  • The alloy, if a drawing calls one out. If not, say what the original was made of.

Attach it to the quote form and write "metal" in the notes.

What still won't be printed

Metal doesn't change the safety rule. Brake, steering and suspension parts, seat belt hardware and anything that holds a person's weight need a certified part with paperwork behind it, not a one-off from a print shop.

Questions

Does Z-Seam offer metal 3D printing in Orlando right now?

Not yet. Metal printing is being added to the shop in Winter Park. You can send the part now, and you get a quote as soon as metal jobs open. If the part can't wait, you'll be told whether carbon-fibre nylon will do the job or whether a machine shop is the better call.

When does a part need to be metal instead of plastic?

When it sits somewhere hotter than plastic can take for long, when its threads get tightened hard or often, when a thin section carries real load, when a surface wears against another part, or when it holds a constant load for years without being allowed to sag.

Is metal 3D printing more expensive than plastic?

Yes, by a wide margin. The material costs more, the machine time costs more, and most metal parts need finishing after they print. That's why every request gets checked first to see whether carbon-fibre nylon would do the same job for less.

Is a 3D printed metal part better than a machined one?

It depends on the shape. Printing wins on shapes a mill can't reach and on one-off parts. Machining wins on simple blocks, flat faces and tight tolerances. Many printed metal parts still get their critical faces and bores machined afterwards.